Square Corten Water Feature Table Kits

£1,395.00

Hand made by craftsmen in the United Kingdom, these square corten water features are the perfect addition to any project for bringing the aesthetic and sound of moving water into the garden. Our kits encompass the full system, including not only the water feature itself but also the pump, pipework, fittings, light set and transformer. To see the full scope of delivery, please refer to the PDF Installation Guide on this page.

Constructed from high quality corten steel, these features will weather beautifully over time to develop the classic long lasting "rusty" patina associated with corten steel. Unlike mild steel, the rusty patina does not flake off over time. Instead the patina actually protects the metal beneath, maintaining its integrity for decades to come.

The construction of these water features is simple, with the corten elements being supplied in two pieces; the basin itself, and the water table. They are built with a foot on each corner that are recessed back slightly, as well as a central reinforcement foot, creating a beautiful shadow gap below the water feature. The basin features an offset overflow pipe that doubles up as the cable entry for the pump and light set. The light set has a "flow-through" design, meaning it acts as both a light set and water spout. The supplied corten cap should be placed over the top of the light set so that it blends in with the rest of the water table. The light set simply plugs into the the supplied outdoor 12v transformer, which should be located away from the water feature.

The pump simply sits inside the feature, pumping water up to the centre of the table before it all cascades back down. The table is designed with a slight lip to hold some of the water before overflowing, almost like a bird bath. The flow of the pump can be adjusted to the desired level using the flow control valve located on the pump. This allows you to choose the perfect balance of flow rate and sound for each project.

These water features are not supplied pre-weathered, and so do require a degree of care and attention on site. Generally, the weathering process would naturally take up to 6 months, however this can be sped up somewhat using spray on solutions. Please refer to the PDF User Manual, Maintenance & Weathering Guide on this page for more detailed instructions.

Please note: These water in these features can become rusty during the weathering process. When this overflows it can stain paving, patios or decking. Please refer to the PDF User Manual, Maintenance & Weathering Guide for more information.

These water features are also available with a round shape measuring Ø 800mm x 400mm (h).

Instructions pdf

Instaltion Manual pdf

Quantity:
Add To Cart

Hand made by craftsmen in the United Kingdom, these square corten water features are the perfect addition to any project for bringing the aesthetic and sound of moving water into the garden. Our kits encompass the full system, including not only the water feature itself but also the pump, pipework, fittings, light set and transformer. To see the full scope of delivery, please refer to the PDF Installation Guide on this page.

Constructed from high quality corten steel, these features will weather beautifully over time to develop the classic long lasting "rusty" patina associated with corten steel. Unlike mild steel, the rusty patina does not flake off over time. Instead the patina actually protects the metal beneath, maintaining its integrity for decades to come.

The construction of these water features is simple, with the corten elements being supplied in two pieces; the basin itself, and the water table. They are built with a foot on each corner that are recessed back slightly, as well as a central reinforcement foot, creating a beautiful shadow gap below the water feature. The basin features an offset overflow pipe that doubles up as the cable entry for the pump and light set. The light set has a "flow-through" design, meaning it acts as both a light set and water spout. The supplied corten cap should be placed over the top of the light set so that it blends in with the rest of the water table. The light set simply plugs into the the supplied outdoor 12v transformer, which should be located away from the water feature.

The pump simply sits inside the feature, pumping water up to the centre of the table before it all cascades back down. The table is designed with a slight lip to hold some of the water before overflowing, almost like a bird bath. The flow of the pump can be adjusted to the desired level using the flow control valve located on the pump. This allows you to choose the perfect balance of flow rate and sound for each project.

These water features are not supplied pre-weathered, and so do require a degree of care and attention on site. Generally, the weathering process would naturally take up to 6 months, however this can be sped up somewhat using spray on solutions. Please refer to the PDF User Manual, Maintenance & Weathering Guide on this page for more detailed instructions.

Please note: These water in these features can become rusty during the weathering process. When this overflows it can stain paving, patios or decking. Please refer to the PDF User Manual, Maintenance & Weathering Guide for more information.

These water features are also available with a round shape measuring Ø 800mm x 400mm (h).

Instructions pdf

Instaltion Manual pdf

Hand made by craftsmen in the United Kingdom, these square corten water features are the perfect addition to any project for bringing the aesthetic and sound of moving water into the garden. Our kits encompass the full system, including not only the water feature itself but also the pump, pipework, fittings, light set and transformer. To see the full scope of delivery, please refer to the PDF Installation Guide on this page.

Constructed from high quality corten steel, these features will weather beautifully over time to develop the classic long lasting "rusty" patina associated with corten steel. Unlike mild steel, the rusty patina does not flake off over time. Instead the patina actually protects the metal beneath, maintaining its integrity for decades to come.

The construction of these water features is simple, with the corten elements being supplied in two pieces; the basin itself, and the water table. They are built with a foot on each corner that are recessed back slightly, as well as a central reinforcement foot, creating a beautiful shadow gap below the water feature. The basin features an offset overflow pipe that doubles up as the cable entry for the pump and light set. The light set has a "flow-through" design, meaning it acts as both a light set and water spout. The supplied corten cap should be placed over the top of the light set so that it blends in with the rest of the water table. The light set simply plugs into the the supplied outdoor 12v transformer, which should be located away from the water feature.

The pump simply sits inside the feature, pumping water up to the centre of the table before it all cascades back down. The table is designed with a slight lip to hold some of the water before overflowing, almost like a bird bath. The flow of the pump can be adjusted to the desired level using the flow control valve located on the pump. This allows you to choose the perfect balance of flow rate and sound for each project.

These water features are not supplied pre-weathered, and so do require a degree of care and attention on site. Generally, the weathering process would naturally take up to 6 months, however this can be sped up somewhat using spray on solutions. Please refer to the PDF User Manual, Maintenance & Weathering Guide on this page for more detailed instructions.

Please note: These water in these features can become rusty during the weathering process. When this overflows it can stain paving, patios or decking. Please refer to the PDF User Manual, Maintenance & Weathering Guide for more information.

These water features are also available with a round shape measuring Ø 800mm x 400mm (h).

Instructions pdf

Instaltion Manual pdf

Spillway Bowl And Basin Fountain Kit – Patina – 32″/40″ Dia (81/102 cm)
Sale Price:£1,738.49 Original Price:£1,829.99
sale
Stacked Slate Urn Fountain Kit sml 24" -61cm high
Sale Price:£550.99 Original Price:£579.99
sale
Aquascape Stacked Slate Sphere Fountain Kits - sphere
from £550.00
sale
Stacked Slate Urn Fountain Kit medium – 33.5″ H (85 cm)
Sale Price:£740.99 Original Price:£779.99
sale
Faux Basalt Column Set of 3 Fountain Kit – 24″, 30″, 36″ H (61, 76, 91 cm)
Sale Price:£1,804.99 Original Price:£1,899.99
sale